The "AC BIG Displays" (iLD-ACC and iLD-ACV) provide accurate isolated measurement of AC Voltage and Current signals.
The AC Voltage model can be scaled for ranges from 0 to 400 mVac through 0 to 400 Vac.
The AC Current model covers ranges from 0 to 10 mA through 0 to 5 Amps AC.
The "Frequency Pulse BIG Display" (iLD-FP) provides accurate isolated measurement of frequency (from 200 Hz to 50 KHz)
and pulse signals (up to 200 M pulses full scale) that can be scaled to any engineering units.
Programmable Color Display
The iLD-ACC, iLD-ACV, and iLD-FP feature BIG bright 7-segment LED's that can be programmed to change colors between RED
, AMBER, and GREEN to indicate visual alarms.
The BIG Display can be mounted flush in a panel or surface mounted with the included brackets. The entire BIG Display enclosure provides NEMA 4/IP65 protection. Whether
panel-mounted or surface-mounted, the BIG Display does not need to go inside a bulky and expensive NEMA enclosure.
Configuration of the iLD-ACC, -ACV, or -FP will be performed using RS-485 communication standard at half duplex and the configuration software that is
available on our website.
With the Ethernet (-EI) option you can "see" your meter and control your process through a web browser over the Internet from halfway around the world.
With the Isolated Analog Output (-C2A) option, user can select output range for 0 to 10V, 4 to 20 mA, or 0 to 20 mA using serial RS-232 and the configuration
software (this eliminates the RS-485 communication available on the standard model).
Factory Scaling (-FS) is available if you prefer the unit to be fully configured before shipment.
Please provide your selections for Factory Scaling settings:
Input Range: 10 mA, 100 mA, 1 A, 5 A
Input Range: 400 mVac, 40 Vac, 400 Vac
Select your Input Range and Display Range Factory Scaling Example: 0 to 5 A = 0 to 50.00
Select your Input Range and Display Range Factory Scaling Example: 0 to 400 Vac = 0 to 6000
Pick from each selection
Mode: Frequency, A-B, Totalize
Excitation: 12.5 V, 5 V, 8 V
Pull up/down: None, 3 K pull-up, 1 K pull-down
Gate Time: in milliseconds
Debounce Time: in milliseconds
Debounce Contact: Yes/No?
Low Level Input: Yes/No?
Frequency Range: 0.2 Hz to 50 KHz
For Frequency Mode select your Input Range and Display
Range Factory Scaling Example for Frequency Mode: 0 to 1 KHz = 0 to 5000
For Totalize and A-B Mode select your Input Range and
Display Range Factory Scaling Example for Total / A-B Mode: 0 to 100 pulses = 0 to 2000 display counts
All dollar amounts on this site are shown in Canadian currency.
Part Number Builder
Build Your Part Number Below
Size of Digit Display select from: 24 for 57 mm (2.25 inch) 4-digit display 44 for 101 mm (4 inch) 4-digit display 26 for 57 mm (2.25 inch) 6-digit display (for FP units only) 46 for 101 mm (4 inch) 6-digit display (for FP units only)
Input Type select from: FP for Frequency/Pulse/Rate/Totalizer Input ACC for AC Current Input ACV for AC Voltage Input
Communication Options select from: Nothing(leave field blank) for No Communication Options -C2A for RS232 and Isolated Analog Output -EI for Ethernet with Embedded Web Server Output
Factory Scaling select from: Nothing(leave field blank) for No Factory Scaling -FS for Factory Scaling no charge - see chart above for required information and examples
Note: All combinations may not be valid, check spec sheet for valid part numbers.