OMEGA’s PX6000 Series pressure
transducers fit easily into your
application. These low-cost
transducers are small and light,
and mounting requires no bulky
structures. You select from
3 electrical terminations and
6 pressure fittings. The sensor is a
small [about 2.54 cm (0.1")] square
silicon chip with 4 diffused strain
gages, mounted in the stainless
steel case. Laser-trimmed resistors
provide temperature compensation
and adjust zero balance and span.
The 30 mV full range output is
compatible with most amplifiers
and data acquisition systems.
The PX6000 uses solid state media
isolation for improved reliability.
Thin films of chemically inert
materials are deposited or grown on
the chip surface to provide electrical
isolation between the sensor and
pressure medium. The sensor is
less sensitive to vibration and
more dependable in high-shock
environments. Corrosion resistance
is outstanding, and the isolation will
remain effective because there is
no gel or oil column to deteriorate.
The PX6000 is also available in metric configurations, with G1/4 or G1/8 ports, and
models from 0-1 to 0-25 bar pressure ranges.
Please see the PXM6000 for complete details, or contact our Pressure department for more information..
SPECIFICATIONS ELECTRICAL Excitation: 10 Vdc Output: 3 mV/V ± 10% Input Resistance: 2000 Ω minimum Output Resistance: 1000 Ω minimum, 1500 Ω maximum Zero Balance: 0 mV ±5% FSO Dielectric Isolation Resistance: 100 MΩ minimum at 50 Vdc applied between the case or a conductive medium and the bridge circuit Sensing Element: 4-active-arm bridge using a micro-machined diffused silicon diaphragm sensor, thin-film media and dielectric isolation barriers Temperature Sensor: Output resistance @ 24°C (75°F) 900 to 1500 Ω Temperature Coefficient: 8% min, 10% max per 55.5°C (100°F)
PERFORMANCE Accuracy: Combined linearity, hysteresis and repeatability ≤±0.25% FS for all ranges
ENVIRONMENTAL Operating Temp Range: -54 to 150°C (-65 to 300°F) Compensated Temp Range: -54 to 121°C (-65 to 250°F) Thermal Effects: Span: ≤±0.02% of FS/°F Zero: ≤±0.02% of FS/°F Vibration Sensitivity: At 35g peak sinusoidal vibration from 10 Hz to 2000 Hz (½" D.A.), the output shall not exceed 0.04% FS/g for 15 psi range to 0.005% FS/g for 100 psi and above Natural Frequency: Greater than 35 kHz for 100 psi and above Shock: 100 g, 11 ms half sine wave without damage
PRESSURE Proof Pressure: 2 times rated pressure will not cause changes in performance beyond the specified tolerances Burst Pressure: 3 times rated pressure for pressure ranges below 200 psi, or 2.5 times rated pressure for pressure ranges above 200 psi will not cause rupture of the pressure sensor
MECHANICAL Wetted Parts: 316 stainless steel, silicon nitride, Pyrex® glass, epoxy, Kovar® Electrical Connection: Standard: PTIH-10-6P Optional: 0.6 m (2') cable or 4-pin solder terminal header Pressure Port: Standard: MS33656-4 male Optional: MS33649-4 female, 1/4-18 or 1/8-27 NPT male or female Weight: 4 oz max, excluding pressure fitting and electrical connection Mating Connector: PTS06A-10-6S (not included)
All dollar amounts on this site are shown in Canadian currency.Note: Metric Ranges Available - Consult Engineering Ordering Example: (1) PX6000L1-100GV is a 100 psi Gage pressure transducer with an MS33649-4 male pressure connection, CAD525.00 plus (1) PTS06A10-6S mating connector (sold separately), CAD60.00, CAD525.00 + 60.00 = CAD585.00
Part Number Builder
Build Your Part Number Below
Pressure Port select from: L for MS33656-4 Male M for MS33649-4 Female A for 1/8-27 NPT Male B for 1/8-27 NPT Female C for 1/4-18 NPT Male D for 1/4-18 NPT Female
Electrical Connection select from: 1 for PT1H-10-6P Connector or equal (mating connector not included) 0 for 2' (6m) cable (std) +2$/ft over 2' 3 for 4-pin Eyelet Header (no charge)
Range select from: 30 for 30 to 0 in-Hg (Vacuum only) 015 for 0-15 psi 020 for 0-20 psi 050 for 0-50 psi 100 for 0-100 psi 200 for 0-200 psi 300 for 0-300 psi
Units select from: VAC for Vacuum Model G for Gage Model A for Absolute Model
Output select from: V for mV/V Output 5T for 0 to 5 Vdc Output I for 4 to 20mA Output
Options select from: for No Options -CAL11 for 11 point NIST Calibration $250 adder -xxFT for Extra length of cable $2/ft over 3ft
Note: All combinations may not be valid, check spec sheet for valid part numbers.