Call us at 1-888-826-6342
Pre-Wired Strain Gauges for Easy Installation
PRE-WIRED STRAIN GagesS, Linear Gagess, X-Y Planar Rosettes (Tee Rosette), 0°/45°/90° Planar Rosettes
Volume discounts available
Volume Discount Schedule
| Quantity | Price each |
|---|---|
| 1-4 | C$296.95 |
| 5-9 | C$282.10 |
| 10-24 | C$276.16 |
| 25-49 | C$264.29 |
| 50-99 | C$258.35 |
| 100+ | C$252.41 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Pre-Wired Gages Make Installations Easy!
- No Soldering at the Measuring Point
- Sold in Packs of Ten
- Each Gage has 50 mm of PTFE Cable before Transitioning to AWG 28 Leads to Prevent Leads from Adhering During Installation
KFH-3-350-C1-11L3M3R Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Grid Length Range
Grid Length
Grid Width
Connection Type
Resistance
Grid Style
Temperature Range Units
Temperature Range Min
Temperature Range Max
STC number
Maximum Strain
Features
Linear pattern precision pre wired gages with minature and medium length grids are for general purpose and stress analysis applications. Available with either two 1-meter leads or three 3-meter leads and 120 Ω or 350 Ω resistance. All models are compensated for steel.
Specifications See Spec Sheet for full specifications
Strain Gage Construction Foil strain gage with embedded measuring grid
Measuring Grid
Material Constantan
Thickness µm (microinch) 3.8 or 5 (150 or 197), depending upon strain gage type
Carrier Material Polyimide
Thickness µm (microinch) 45 ± 10 (1.772 ± 394)
Connections PTFE wire, Ø - 0.051 mm², approximately 50 mm long, connected to AWG 28 ribbon cables (PVC insulated) through solder sleeves in 2- or 3-wire configurations
Nominal Resistance Ω 120 or 350 depending upon gage
Resistance Tolerance % ±0.35, with 0.6 mm and 1.5 mm grid length % ±1
Gage Factor approximately 2 (stated on package)
Gage Factor Tolerance % ±1, with 0.6 mm and 1.5 mm grid length % ±1.5, temperature coefficient of gage factor 1/K [1/°F] (115 ± 10) x 10-6 [(64 ± 5.5) x 10-6, nominal value of gage factor temperature coefficient Specified on each package
Applicable Bonding Materials
Cold Cure Adhesives SG496, SG401
Heat Cure Adhesives TT300
Specifications See Spec Sheet for full specifications
Strain Gage Construction Foil strain gage with embedded measuring grid
Measuring Grid
Material Constantan
Thickness µm (microinch) 3.8 or 5 (150 or 197), depending upon strain gage type
Carrier Material Polyimide
Thickness µm (microinch) 45 ± 10 (1.772 ± 394)
Connections PTFE wire, Ø - 0.051 mm², approximately 50 mm long, connected to AWG 28 ribbon cables (PVC insulated) through solder sleeves in 2- or 3-wire configurations
Nominal Resistance Ω 120 or 350 depending upon gage
Resistance Tolerance % ±0.35, with 0.6 mm and 1.5 mm grid length % ±1
Gage Factor approximately 2 (stated on package)
Gage Factor Tolerance % ±1, with 0.6 mm and 1.5 mm grid length % ±1.5, temperature coefficient of gage factor 1/K [1/°F] (115 ± 10) x 10-6 [(64 ± 5.5) x 10-6, nominal value of gage factor temperature coefficient Specified on each package
Applicable Bonding Materials
Cold Cure Adhesives SG496, SG401
Heat Cure Adhesives TT300
Rated 5 out of
5
by
MSilva from
Great performance
Precise. We will keep using this sensor from Omega.
Date published: 2017-08-09
Rated 3 out of
5
by
smlt from
I only buy these when I run out of others.
These gages work fine once I get them installed. But the heavy wire splices near the gage complicates installation. The hook up end is just a tiny bit of bare wire - my preferred brand always makes long tinned ends which can be put directly around a screw terminal.
Date published: 2016-06-13
Rated 5 out of
5
by
Anonymous from
PRE-WIRED STRAIN GagesS
When it comes to measuring strain in various applications, the convenience and accuracy of the equipment you use can make a significant difference. In this review, we will be discussing the merits of Pre-Wired Strain Gauges, a tool that has increasingly gained popularity in the world of engineering and materials testing.
Date published: 2023-10-23
Rated 5 out of
5
by
Tom H from
Easy
Prewired saves me the effort of soldering. I have applied these to over 20 prototype devices that require force feedback. They have functioned reliably for "long" periods of time (2 years and counting) I apply them to Aluminum plates with Loctite 401.
Date published: 2022-10-21
Does each linear pre-wired strain gauge contain a full Wheatstone bridge or would I have to purchase 4 to create one myself?
The KFH is a linear, single grid strain gauge. It is not a full Wheatstone bridge. Our Tech Support has emailed you a diagram of what complete Wheatstone bridge likes. Please contact our Tech Support if you have any further questions. Thank you.
Date published: 2020-02-18
Is this priced per pack of 10?
Thanks for your question. Yes, these are priced per pack of ten.
Date published: 2019-04-22
Can these gauges be reused after being removed from a specimen?
Thank you for your question?
Most strain gauges will not work once they have been removed from a glued surface.
However you can try and have had some customers succeed in doing it onetime.
Date published: 2019-06-25
