Appelez-nous au 1-888-826-6342
Shear, Full Bridge Strain Gauges with Transducer Quality
1.8 mm Grid Length, 5 mm Grid Width 350 Ω Resistance, ST STC Number
Remises de volume disponibles
Calendrier de remise sur volume
| Quantité | Prix unitaire |
|---|---|
| 1-4 | C$268.30 |
| 5-9 | C$254.89 |
| 10-24 | C$249.52 |
| 25-49 | C$238.79 |
| 50-99 | C$233.42 |
| 100+ | C$228.06 |
Ajouté à votre panier
Configuration terminée.
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Échec de l'enregistrement des configurations, cliquez sur le bouton Configurer Recommencer
- Precision Transducer Quality Gages
- 350 or 700 ohm Bridges
- compensated for Steel or Aluminum
- 2 Half Bridge Pattern can be used a 1 Full Wheatstone Bridge
SGT-2DD/350-SY11 Options de modèles
Voir tous les modèlesModifiez ces spécifications pour commander un modèle différente. Toutes les combinaisons ne sont pas valides. Les options compatibles avec les sélections précédentes seront en gras.
*Les options en surbrillance ne sont pas compatibles. Veuillez sélectionner une combinaison différente.
Grid Length
Grid Width
Connection Type
Resistance
STC number
Grid Style
Grid Length Range
Temperature Range Units
Temperature Range Min
Temperature Range Max
Maximum Strain
Features
OMEGADYNE® offers full bridge transducer quality strain gages for shear and torsional strain applications. These strain gages can be used in transducer design for shear beam load cells, or they can also be used for reaction torque on a shaft.
SGT-2DD/350-SY** has 2 half bridges on one carrier piece. Each half bridge has a dual shear pattern, with opposite grids and a common lead/solder pad. SGT-3/700-FB** has 4 independent shear strain gages, with opposite grid angles, on one carrier, with separate leads/pads (electrically independent). Below we show one wiring example SGT-2DD/350-SY** used to measure a reaction torque on a shaft. The strain gages have been numbered, and the leads/solder pads labeled.
SGT-2DD/350-SY** has 2 half bridges on one carrier piece. Each half bridge has a dual shear pattern, with opposite grids and a common lead/solder pad. SGT-3/700-FB** has 4 independent shear strain gages, with opposite grid angles, on one carrier, with separate leads/pads (electrically independent). Below we show one wiring example SGT-2DD/350-SY** used to measure a reaction torque on a shaft. The strain gages have been numbered, and the leads/solder pads labeled.
Rated 5 out of
5
by
rtuckr from
Accurate Strain Guages
Easy to install and calibrate. I used on a Torque measurement with good success.
Date published: 2017-04-20
Rated 5 out of
5
by
Erick4 from
Worked how it should.
Installed it and it worked as it should. No issues.
Date published: 2016-03-11
Are these gages encapsulated? Also, is it recommended to further encapsulate the gage with adhesive after installation if used outside?
Yes these gauges are encapsulated in a polyimide carrier. If used outdoors we suggest apply some sort on addition coating over the gages. A flexible rubber sealant would probably work well
Date published: 2021-02-25
What is the gauge factor for the SGT-2DD/350-SY11 ?
WeldingRod the gage factor for the SGT series will be 2.00 +/- 5%. If you have any further questions please send an email to pressure@omega.com.
Date published: 2020-04-24
Can I use those cells for a torque monitoring application. If yes, then how long those last without failing for fatigue use. Im in a project that needs to have everything pretty small, and those cells may fit well. Thanks
Yes you can use these gages for torsional (torque) measurement on a shaft. Life should indefinite as long as you do not exceed the maximum strain rating of the gage.
Date published: 2021-04-20
For clarity, is item # SGT-3/700-FB41 sold in packets of 5 for $105 ($21 ea)?
Neil,
Thank you for contacting Omega Engineering. Yes they are indeed sold in packs of 5:
SGT-3/700-FB41
$105.00 (For pack of 5)
STRAIN GAUGES - PACK OF 5
Thank you.
Date published: 2019-09-16