Call us at 1-888-826-6342
Call us at 1-888-826-6342.
Industrial, Low Profile Accelerometers
Low Profile Industrial Grade Accelerometers
Volume discounts available
Volume Discount Schedule
| Quantity | Price each |
|---|---|
| 1-9 | C$416.40 |
| 10-24 | C$395.58 |
| 25-49 | C$387.25 |
| 50-99 | C$370.60 |
| 100-199 | C$362.27 |
| 200+ | C$353.94 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Corrosion Resistant
- Reverse Wiring Protection
- Rugged Industrial Design
- Ground Isolated
- ESD Protection
ACC787A Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Acceleration Range
Frequency Range (Nominal)
Output Type
Mounting Type
Features
The OMEGAROMETER Series accelerometers are one of the best accelerometers designed for industrial vibration measurements. These accelerometers feature a hermetically sealed 316L stainless steel case suitable for harsh environments. The ACC787A is a general purpose accelerometer with a low profile side cable exit.
SPECIFICATIONS
DYNAMIC
Sensitivity, ±10%, 25°C (77°F): 100 mV/g
Acceleration Range1: 80 g peak
Amplitude Non-Linearity: 1%
Frequency Response:
±10%: 1.0 to 5000 Hz
±3 dB: 0.7 to 10,000 Hz
Resonance Frequency: 22 kHz
Transverse Sensitivity, Max: 5% of axial
ELECTRICAL
Power Requirement:
Voltage Source1: 18 to 30 Vdc
Current Regulating Diode1,2: 2 to 10 mA
Electrical Noise, Equiv. g Nominal:
Broadband: 2.5 Hz to 25 kHz: 700 µg
Spectral:
10 Hz: 10 µg√Hz
100 Hz: 5 µg√Hz
1000 Hz: 5 µg√Hz
Output Impedance, Max: 100 Ω
Bias Output Voltage, Nominal: 12 Vdc
Grounding: Isolated case, internally shielded
ENVIRONMENTAL
Temperature Range: -50 to 120°C (-58 to 248°F)
Vibration Limit: 500 g peak
Shock Limit: 5000 g peak
Electromagnetic Sensitivity, Equiv. g, Max: 70 µg/gauss
Sealing: Hermetic to 10-8 cc/s
Base Strain Sensitivity, Max: 0.002 g/microstrain
PHYSICAL
Weight: 145 g (5.1 oz)
Case Material: 316L SS
Mounting: ¼-28 captive hex head screw with 1.2 mm (0.046') diameter safety wire hole
Connector: 2 pin, MIL-C-5015 style
Connections:
Pin A: Power/signal
Pin B: Common
Mating Connector: Amphenol 97-3106A-10SL-4S type
Recommended Cabling: ACC-CB7-10
NOTES:
1 To minimize signal distortion when driving long cables or high-vibration signals, 24 to 30 Vdc powering is recommended. The higher-level constant current source should be used when driving long cables.
2 A maximum current of 6 mA is recommended for operating temperatures above 100°C (212°F).
SPECIFICATIONS
DYNAMIC
Sensitivity, ±10%, 25°C (77°F): 100 mV/g
Acceleration Range1: 80 g peak
Amplitude Non-Linearity: 1%
Frequency Response:
±10%: 1.0 to 5000 Hz
±3 dB: 0.7 to 10,000 Hz
Resonance Frequency: 22 kHz
Transverse Sensitivity, Max: 5% of axial
ELECTRICAL
Power Requirement:
Voltage Source1: 18 to 30 Vdc
Current Regulating Diode1,2: 2 to 10 mA
Electrical Noise, Equiv. g Nominal:
Broadband: 2.5 Hz to 25 kHz: 700 µg
Spectral:
10 Hz: 10 µg√Hz
100 Hz: 5 µg√Hz
1000 Hz: 5 µg√Hz
Output Impedance, Max: 100 Ω
Bias Output Voltage, Nominal: 12 Vdc
Grounding: Isolated case, internally shielded
ENVIRONMENTAL
Temperature Range: -50 to 120°C (-58 to 248°F)
Vibration Limit: 500 g peak
Shock Limit: 5000 g peak
Electromagnetic Sensitivity, Equiv. g, Max: 70 µg/gauss
Sealing: Hermetic to 10-8 cc/s
Base Strain Sensitivity, Max: 0.002 g/microstrain
PHYSICAL
Weight: 145 g (5.1 oz)
Case Material: 316L SS
Mounting: ¼-28 captive hex head screw with 1.2 mm (0.046') diameter safety wire hole
Connector: 2 pin, MIL-C-5015 style
Connections:
Pin A: Power/signal
Pin B: Common
Mating Connector: Amphenol 97-3106A-10SL-4S type
Recommended Cabling: ACC-CB7-10
NOTES:
1 To minimize signal distortion when driving long cables or high-vibration signals, 24 to 30 Vdc powering is recommended. The higher-level constant current source should be used when driving long cables.
2 A maximum current of 6 mA is recommended for operating temperatures above 100°C (212°F).
RoHS 2015/863 - View Certificate
CE Approved
UKCA
I need your confirmation about the maximum distance between the sensor and the PLC, in this moment our client have 70 meters between sensor and PLC, I need confirmation about the required cable for this sensor. The client have a model 1756-IA16I.
Cabling for accelerometers need to kept as short as possible. If you are need to run a signal a long distance you would have to convert the signal 4 to 20mADC signal. Omega does not offer this type of signal conditioning. We suggest you contact someone like Dytran Instruments for a complete system consisting of the sensor, cabling and signal conditioning
Date published: 2021-09-09
Accessories