PST joins DwyerOmega. Read more>
Linear Strain Gages
6 mm Grid Length, 6.3 mm Grid Width 350 Ω Resistance
Volume discounts available
Volume Discount Schedule
| Quantity | Price each |
|---|---|
| 1-4 | C$177.04 |
| 5-9 | C$168.19 |
| 10-24 | C$164.65 |
| 25-49 | C$157.57 |
| 50-99 | C$154.02 |
| 100+ | C$150.48 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Conveniently Priced per Pack of 10
- 1-Axis Linear Gages for Static and Dynamic Applications
- Small Bending Radius
- Broad Temperature Range
SGD-2/350-LY11 Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Grid Length Range
Grid Length
Grid Width
Connection Type
Resistance
STC number
Grid Style
Temperature Range Units
Temperature Range Min
Temperature Range Max
Maximum Strain
OMEGA™ uni-axial strain gages are available in a variety of models to cover most strain measurement applications. Their rugged construction and flexibility make them suitable for highly accurate static and dynamic measurement. The measuring grid is formed by etching constantan foil, which is then completely sealed in a carrier medium composed of polyimide film.
Rated 5 out of
5
by
Victory16 from
excellent
It is perfect for my project. It is happy to purchase this one.
Date published: 2016-10-28
Rated 5 out of
5
by
Anonymous from
Dynamic experimental setup (SHPB)
This Gage is easy to used with lab experimental setup.
Date published: 2020-05-31
Rated 4 out of
5
by
Walker678 from
Pretty straightforward strain guahe
Purchased to use for a power meter on a bicycle. They are working well now that I have them hooked up, but getting them on properly was a bit of work. I have only done this once before but last time I remember it being easier. I couldn't get the pads to wet with solder for a long time and had the pads rip off on a few by accidentally pulling on the cables (lightly) once they were hooked up. Probably my own fault, but I did barely touch them. I put on a new pair and smothered them in superglue, they are stellar now.
Date published: 2018-03-28
Rated 4 out of
5
by
Marco B from
Timely Delivery, but Room for Improvement
The strain gauges arrived earlier than expected, which was impressive and greatly appreciated. The packaging was mostly secure, but one group was fastened with a rubber band that slightly compressed them. Thankfully, there was no damage, but more attention to this detail would ensure a flawless experience next time.
Date published: 2024-11-28
Rated 5 out of
5
by
Gary H from
Efficient delivery and high product quality
The product of strain gauges were delivered very efficiently such that we were able to eliminate any possible delay for our important testing. In the meantime, the quality of Omega strain gauges is the best of the peer products from other manufacturers.
Date published: 2023-04-03
Rated 5 out of
5
by
Asdfgh from
Rock crusher strain gauge testing
Worked perfectly on cast high strength steel of a rock crusher
Date published: 2023-02-09
Rated 5 out of
5
by
AmyS from
Omega is a Great Supplier.
Omega is a Great Supplier and very pleased with the quality of their products.
Date published: 2022-08-18
Rated 5 out of
5
by
Derek Bautista from
Awesome
Great quality strain gauges, awesome customer service!
Date published: 2021-04-30
The description and item number dont match
JBOB, the SGD-3/350-LY11 stands for 3 mm grid, the 350 stands for 350 ohm and the LY stands for Linear. The description is incorrectly marked as 120 ohm. Please go with description on the spec sheet
https://assets.omega.com/pdf/test-and-measurement-equipment/strain-gauges/SGD_LINEAR1-AXIS.pdf
Date published: 2021-01-25
How much required voltage is needed to get the strain gauges to function/record data properly?
Joejoe2768 Thank you for contacting Omega Engineering, the max V rms will be listed in the spec sheet corresponding to each strain gauge based on grid length and width.
Date published: 2020-09-15
Is it $52 per sensor or $52 for a pack of 10?
JoeJj Thank you for contacting Omega Engineering, this price will be for a pack of 10
Date published: 2020-09-15
What is the recommended Wheatstone bridge configuration that you would recommend for these particular strain gauges and preferably one that is compatible with multiple sensors at once? Thank you.
These gauges can be used in a 1/4,1/2 of full bridge configuration. Full bridge best due to it having the highest sensitivity.
Date published: 2020-10-06
Description and the item number dont match.
Hello, the description on the page is incorrect, we are working to fix it.
Please see the spec sheet for the right description: https://assets.omega.com/pdf/test-and-measurement-equipment/strain-gauges/SGD_LINEAR1-AXIS.pdf
Please email pressure@omega.com for more details
Date published: 2021-01-30
Good Day, I have reviewed your datasheets but I am not able to find detailed information about the strain gauges you offer. What is the maximum deflection of your gauges? What is the relationship with the change in resistance? Thank you.
Thank you for contacting Omega with your question. Specifications for the strain gages can be found in the Technical Reference section on our website under the heading “Pressure, Strain and Force Related”. Here is a link to the site for the spec sheet
https://www.omega.co.uk/techref/pdf/STRAIN_GAGE_TECHNICAL_DATA.pdf
Date published: 2021-02-23
is this a 350 gage or 120? Description says one thing and the item number is: SGD-3/350-LY11
JBOB, the SGD-3/350-LY11 stands for 3 mm grid, the 350 stands for 350 ohm and the LY stands for Linear. The description is incorrectly marked as 120 ohm. Please go with description on the spec sheet
https://assets.omega.com/pdf/test-and-measurement-equipment/strain-gauges/SGD_LINEAR1-AXIS.pdf
Date published: 2021-01-25
The description says these gauges have a "broad temperature range". Are there some materials (like Aluminum or steel) that they are specifically compensated to,or are these essentially non-compensated gauges?
If you look at Data Sheet pdf for the SGD gages you will that there are 3 variation of Temperature Compensation. AL for Aluminum. ST for Steel/Stainless Steel. UNC for Uncompensated.
Date published: 2021-01-09