Appelez-nous au 1-888-826-6342
Thermocouple à Rondelle Boulonné
Bolt-On Washer Thermocouple Assemblies
Remises de volume disponibles
Calendrier de remise sur volume
Quantité | Prix unitaire |
---|---|
1-9 | C$31.02 |
10-24 | C$29.47 |
25-99 | C$27.92 |
100-499 | C$26.37 |
500-999 | C$24.82 |
1000+ | C$23.27 |
Ajouté à votre panier
Configuration terminée.
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Veuillez ajouter au panier pour la conserver ou quitter la configuration
Échec de l'enregistrement des configurations, cliquez sur le bouton Configurer Recommencer
- Thermocouples J, K, T, et E
- Nouvelle conception résistante
- Pour les tailles de vis M3,5 , M4, M4,5 et M6
- Fait de fil tolérance classe 1 isolé PFA ou verre dia. 0,8 mm
- Disponibles en longueurs de 300 mm, 600 mm, 1,0 m, et 1,5 m avec fils terminaux foirés
- Jusqu'à 480°C nominal pour isolation de verre
- Jusqu'à 260°C pour isolation PFA
OPTIONS DISPONIBLES - Longueurs de fils spéciales
- Connecteurs thermocouple au lieu de fils avec terminaux foirés
WTK-6-36 Options de modèles
Voir tous les modèlesModifiez ces spécifications pour commander un modèle différente. Toutes les combinaisons ne sont pas valides. Les options compatibles avec les sélections précédentes seront en gras.
*Les options en surbrillance ne sont pas compatibles. Veuillez sélectionner une combinaison différente.
Thermocouple Type
Process Temperature Range
Cable Insulation
Termination Connection Type
Cable Length
Additional Features
Mounting Style
Probe Diameter
Minimum Temperature Measurement
Features
Category
Sensor Application
Color Code Standard
Description
Un ensemble de thermocouple qui peut être facilement monté à de multiples surfaces. Parfaitement adaptable à plusieurs appareils de mesure de température en surface sur lesquels le montage fixe est possible.EXEMPLES DE MODELES COURANTS CI-DESSOUS. VEUILLEZ UTILISER LE TABLEAU CONSTRUCTEUR DE REFERENCE POUR TROUVER LES MODELES SPECIFIQUES QUI SONT DISPONIBLES.
Pour les spécifications complètes des produits, veuillez consulter la section "Liens associés" en bas de page.
Dimensions de la rondelle
M3,5 et M4 : L 22 x L 6,5 mm
M4,5 et M6: L 25 x L 9 mm
Rated 5 out of
5
by
Audrey Overlie from
Thermocouple perfection
The parts were exactly what the team was looking for in an assembly process
Date published: 2024-01-08
Rated 5 out of
5
by
John B from
Just what we needed
These thermocouples were the form factor we needed for our application. They will work great
Date published: 2023-01-24
Rated 5 out of
5
by
Ray Francis from
just what I needed
the part was out of stock but they still came in a timely manner and worked as excepted, will be a repeat customer
Date published: 2022-11-17
Rated 5 out of
5
by
Harvey Melber from
Rock-On for the Bolt-On Washer!
The part met our specs precisely and was in great condition and appropriately priced.
Date published: 2022-11-03
Rated 5 out of
5
by
TheKAG from
Solid thermocouple
So far so good with this thermocouple. One recommendation I do have, double/triple check the connector before ordering. I thought I ordered the right one, but ended up having to order a replacement. Top to Omega, add images of the termination chosen to the spec wizard.
Date published: 2021-01-04
Rated 5 out of
5
by
Mr Merkin from
Technical staff helped me get all the right parts!
Just what I was looking for! Great support from your technical staff!
Date published: 2020-08-23
Is there a min/max torque for these thermocouples? Are there any other boundary conditions to be aware of when attaching these?
Thank you for your inquiry lbarret. Please send an email to tech support at temp@omega.com.
Date published: 2022-01-13
Does the 0°F lower process limit apply to thermocouple types other than type J? (e.g. can a type T version of the 'WT' sensor accurately measure temperatures below 0°F?)
Thank you for your inquiry. We do not state an accuracy for SLE Wire-Made Products below 0°C (32°F). Can they measure below 0°C? The answer is YES, however, accuracy shows it is no longer linear. If you want an accuracy for a SLE Product we suggest that you get a CAL-4 Calibration Report at an additional cost for temperatures below 0°C.
Date published: 2023-03-01
Two Questions: 1. Where is the thermocouple measurement made? Can you cut off the bolt hole without affecting the performance? 2. Are these made in an un-bent configuration?
Thank you for the inquiry. The thermocouple tip ( sensing portion of the TC) is pressed within the washer. You will notice the small channel on the shoulder of the washer. You could cut off the bolt hole being careful not to cut in to the channel.
We do not offer a flat version.
Best regards
OMEGA
Date published: 2020-04-23
Hello, Does this thermocouple UL listed/certified? If so, can you tell me the UL file No? Thanks,
Thank you for your inquiry Thomson. No, this thermocouple is not UL listed/certified.
Date published: 2022-10-20
What are the wire colors WTJ-6-36-TT
Thank you for your inquiry! The WTJ-6-36-TT is a type J thermocouple so the wires will be red and white.
Date published: 2021-02-17
Are any of these t/c made with stranded wire? I need something that is flexible. If so, what is the Dynamic Bend Radius?
Hi Greg,
These are all made with solid wire. Please use 3 x wire diameter for minimum bend radius. Thinner wire will hold up longer. You might consider the SA1-K or the SA1XL-K as alternate.
Best regards
OMEGA
Date published: 2020-04-09
Could you please inform resistance between wire red and white of thermocouple WTJ-6-12 ? We have to use it to refer of measuring voltage create from this part.
Thank you for your inquiry. We believe the best assistance would come from speaking to us directly at 888-826-6342 ask for the Temperature Department Mon. – Fri. (HOURS 8:30AM - 5:30PM EST).
Date published: 2023-10-02
For the WTK14-60 washer housing, the spec shows the total length is 1" (25mm). But it seems there is a bend on the length and what's the actual length for the contact surface? Thx
Thank you for your inquiry. The length of the bend is approx. 0.45"
Date published: 2023-10-01